IDTechEx-Emerging Technologies - Home
Electrically Conductive Adhesives Enabling Low Temperature Electronics
Rachel Gordon
APR 11, 2016 18:09 PM
A+ A A-

Electrically Conductive Adhesives Enabling Low Temperature Electronics

by Rachel Gordon

Materials are needed to replace the estimated 50,000 metric tons of tin-lead solder currently used each year, but there are no "drop-in" replacements. $1.2 billion of Electrically Conductive Adhesives (ECAs) are already selling each year, and they are becoming increasingly common to replace solders in a variety of functions, applications and industries. 

There are three main categories of conductive adhesives available as safe and environmentally-sound solder alternatives. ECAs consist of a polymeric resin (such as an epoxy, or a silicone) that provides physical and mechanical properties such as adhesion, mechanical strength and impact strength, and a metal filler (such as silver, gold or nickel) that conducts electricity. In order to reduce the volume of filler used, increase the electrical conductivity, and decrease the finest possible pitch width, there is research into using nanoparticle fillers including silver nanowires, silver nanoparticles, nickel nanoparticles and carbon nanotubes.

Figure: Diagram showing some of the most important parameters to consider when choosing an Electrically Conductive Adhesive.

Obviously in all these materials, the electrical conductivity is of primary importance. However, the thermal conductivity must also be high enough so that components do not overheat. The thermal conductivity of ICP is approximately 20 W/m.K, compared to 60 W/m.K for lead solders. Adhesion to the mating surfaces must be good enough so that there will not be adhesive failure, and the tensile strength must be high enough to avoid cohesive failure, even under bending and flexing conditions. The viscosity must be low enough for easy dispensing, but high enough after curing to avoid pump out and dry out. In some applications, the operating temperature will be important, and while solders can operate up to 270ºC, ECAs are limited to around 200ºC. It must be non-toxic, because there is no point replacing lead with another equally toxic material.

Lead solder melts at 215ºC; isotropic conductive paste can be cured as low as 110ºC. This opens up possibilities for using plastic substrates to allow a new generation of flexible electronics. In order to use PET substrates, without the risk of buckling or warping during curing, the cure temperature needs to be brought below 80ºC. 

There are a wide variety of applications for ECAs, but some of the key ones include:

  • Photovoltaic modules - ECAs have suffered from poor stability when applied to copper and tin metals, but improved ECAs for PV applications have been available since 2010. Lower temperature interconnections can allow thinner wafers, and reduce warpage and breakage of solar cells.
  • LCD and OLED displays - ACFs have found a particular niche market in packaging flat panel displays. In general, bending or physical deformation of ECAs can degrade the electrical conductivity. Therefore, novel flexible electrically conductive materials which respond well to repeated bending or high elongations will be required for future flexible display technologies.
  • Touch panels - The damage to the substrates can be reduced by lowering the bonding temperature during assembly. The penetration of touch panels in the cell phone market is forecasted to reach more than 40% in the near future.
  • LEDs - It is quick and cheap to mount LEDs using conductive adhesives and the thermal penalty is tolerable if the adhesive layer is kept thin.
  • RFID chips - Conductive adhesives are used for mounting temperature-sensitive chips on smart cards, because of low curing temperatures.

Currently, 74% of Anisotropic Conductive Film (ACF) is used in the manufacture of LCD or OLED displays. Displays are becoming more widely used in consumer electronics, aerospace, defence, automotive, and infrastructure sectors. UV-thermal cure mechanisms must be developed to lower cure temperature to allow plastic substrates for flexible displays. However, this market is still set to diversify with the market for ACF in non-display applications reaching over $1 billion by 2026, due to the reliable properties, thinness and ease of processing.

Learn more about ECAs at the IDTechEx Show! in Berlin, April 27-28.

FIRST
PREV
NEXT
LAST
Page(s):
[%= name %]
[%= createDate %]
[%= comment %]
Share this:
Please login to enter a comment:
RESET

Computing Now Blogs
Business Intelligence
by Keith Peterson
Cloud Computing
A Cloud Blog: by Irena Bojanova
The Clear Cloud: by STC Cloud Computing
Careers
Computing Careers: by Lori Cameron
Display Technologies
Enterprise Solutions
Enterprise Thinking: by Josh Greenbaum
Healthcare Technologies
The Doctor Is In: Dr. Keith W. Vrbicky
Heterogeneous Systems
Hot Topics
NealNotes: by Neal Leavitt
Industry Trends
The Robotics Report: by Jeff Debrosse
Internet Of Things
Sensing IoT: by Irena Bojanova